http://reality-xp.com/support/trainingc ... XPlane.pdf
quindi da quanto leggo il GPS e' in una finestra popup ( tra l'altro ridimensionabile )
poi se TUTTI gli sviluppatori avranno voglia di riprendere in mano i loro aerei per dare la possibilita' di sostituire fisicamente il GPS di default con questo qui sara' una cosa ben gradita.
La vedo dura che Carenado ci fa' il favore di questo lavoro immane.
se volete vi dico che sicuramente sara' possibile con un click magico sostituire al volo tutti i GPS anche perche' personalmente vivo bene lo stesso
comunque appena lo compro si sciogliera' questo arcano dilemma....
Pace e bene a tutti
REALITY XP GTN 650/750 TOUCH XPLANE
Getting Started
!
The GTN 650/750 Touch plug-in loads with X-Plane
automatically and is always available to any aircraft.
Select Reality XP GTN XPlane menu
to add or remove a GTN
Touch unit to your aircraft, or to change any of its options.
Note: some options require a minimum X-Plane version 9.42
to function properly.
Using The Mouse
This gauge implements a relatively unique implementation of click spots. They work as follows:
•
As the mouse cursor passes over a click spot it changes
from an arrow cursor to a “hand” cursor.
•
Whenever a single click spot is used, a left click will accomplish the task.
•
Knobs work with both left clicks and the mouse wheel. Left clicks turn the knob to the counter-
clockwise direction when the mouse is in an area to the left of the knob and to the clockwise direction
when the mouse is in an area to the right of the knob. Mouse wheel turns the knob in either direction
regardless if the mouse is to the left or to the right of the knob.
•
Touchscreen actions are carried naturally with single clicks or click-and-drag. Mouse wheel simulates
pinch-in and pinch-out actions.
Adjusting Gauge Size
The simulation window resizes with the mouse cursor grabbing any of its edges or corners. In addition,
pressing and holding the SHIFT key while resizing constrains the window size to the correct gauge
aspect
ratio.
Persistent Settings
Every time an aircraft loads a GTN Touch the plugin sets the last known window size, window position and
mode/unit. These settings and others are saved automatically to a file in the aircraft folder. The settings file
name saved in the aircraft folder is:
"RealityXP.GTN.INI"
Keyboard Shortcuts
To change hotkeys, use the Plugin Admin Menu. These are
saved in a "RealityXP.GTN.INI" file located in the X-Plane
preference folders
.
Menu Settings
Master Device
when using 2 GTN at the same time, the "master" controls the autopilot.
Audio Panel (reboots)
enable or disable audio panel and reboot the unit. (GTN 750 only)
Transponder (reboots)
enable or disable the transponder panel and reboot the unit.
Shadin Air Data
enable or disable Shadin Air Data input.
Shadin Fuel Data
enable or disable Shadin Fuel Data input.
Reduce Refresh Rate
reduce GTN screen refresh rate by half.
GPS -> Autopilot
connect the GTN to the autopilot.
GPS -> HSI
connect the GTN to the HSI (displays vertical and horizontal deviation)
GPS -> HSI/CRS (out)
the GTN drives the HSI motor ans sets the course when DTK changes.
GPS <- HSI/OBS (in)
the GTN receives HSI OBS course signal.
GPS -> VOR Indicator
the GTN drives the VOR needles.
CDI -> NAV#/GPS
the GTN CDI mode controls XPlane NAV#/GPS selector.
Auto Select GPS/VLOC
the GTN automatically switches from GPS to VLOC on approach.
Switch to (Co)Pilot Side
connect the GTN either to the Pilot or the Copilot side instruments.
Switch to COM#/NAV#
connect the GTN either to COM1/NAV1 or COM2/NAV2.
Switch to TAWS-# (reboots)
cycle through TAWS-A, TAWS-B and TERR modes.
Switch to System(Simulator) Time
select PC or XPlane clock.
Show Window
show or hide the gauge window.
Reset Window
reset default GTN gauge size.
Freeze Window
locks window dimensions.
Display tooltips
show or hide mouse tooltips.
Make window stack
make this GTN window the top of the stack, the other adjusts below.
...
